EziPly™ is a high-performance structural plywood range designed for New Zealand conditions. Manufactured from FSC® certified radiata pine face veneers over a hardwood core and bonded with exterior phenol-formaldehyde resin, EziPly provides reliable strength, stability and durability for a wide variety of building applications.
EziPly™ is manufactured to AS/NZS 2269:2012 and supplied in a range of grades, sheet sizes and thicknesses to suit residential, commercial and light industrial projects. Available untreated or H3.2 treated, it is suitable for wall bracing, diaphragms, structural flooring, roof sarking, roofing and deck substrates, internal linings and concrete formwork when designed and installed in accordance with NZS 3604, NASH 2019 or Specific Engineering Design.
Every EziPly™ panel is built for structural performance and consistent quality.
Manufactured to AS/NZS 2269:2012 with exterior bond for long-term structural performance.
The EziPly™ range covers structural CD and DD grade plywood, tongue-and-groove structural flooring and roofing panels, and phenolic film-faced Formply. Tongue-and-groove edges provide load sharing between sheets and allow flooring and roof diaphragm action where required, while square-edge panels cover general structural sheathing and bracing needs.
EziPly™ integrates easily into NZ standard construction. As part of a compliant structural system, it can be used in timber or light-gauge steel framed buildings where the primary structure is designed in accordance with NZS 3604, NASH 2019 or Specific Engineering Design. Bracing performance must be taken from a published P21-tested system, and diaphragm, flooring and roofing applications must follow the relevant clauses of NZS 3604.
Structural plywood bracing elements installed to a tested P21 system, providing racking resistance to wind and earthquake loads.
Tongue-and-groove structural flooring panels for floors and floor diaphragms, designed in accordance with NZS 3604 Sections 7.2 and 7.3.
Roof sarking fixed directly to rafters or truss top chords, and plywood substrates beneath waterproofing membranes where part of a certified roofing or deck system.
Non-structural internal linings, substrates and phenolic film-faced Formply for concrete formwork, beams, slabs, lift cores and foundations.
Manufactured to AS/NZS 2269:2012 with F8, F11 and F17 strength grades for dependable performance in structural applications.
One panel range for bracing, diaphragms, structural flooring, roofing, internal linings and concrete formwork.
Easy to cut, drill, nail and screw using standard tools, with tongue-and-groove options for simple, secure floor and roof joints.
Available untreated or H3.2 treated in accordance with AS/NZS 1604.3. When detailed and protected from long-term moisture, meets NZBC B2 Durability requirements.
Manufactured from responsibly sourced fibre with FSC® certification available, supporting responsible forestry and chain-of-custody assurance.
Supplied with a 150-grit sanded face for efficient preparation and finishing where sheet surfaces remain visible or receive coatings.
General structural plywood for wall bracing, diaphragms, sarking and general construction use.
Interior plywood for lining and general interior applications where a clean sanded finish is required.
• Sheet sizes: 2400 x 1200 mm, 2700 x 1200 mm
•Thicknesses: 9 mm, 12 mm
•Face Grade : CD
Tongue-and-groove flooring panels for structural floors and floor diaphragms.
Tongue-and-groove roofing panels for roofing
Film faced ply generally used for large concrete structures.
EziPly™ is supported by comprehensive technical literature and independent test reports. The Specifier and Installer Guide includes design guidance, scope of use, installation requirements, health and safety information and warranty conditions. Additional resources such as Material Safety Data Sheets and detailed test reports are available on request.
For further documentation or support, please contact our sales team at sales@iti.net.nz.
